5 in 1 Metal can cooler with bottle opener, Sublimation ready blanks R – ACC Sublimation Blanks & Designs

May 12,2024

Metal can holder for sublimation. White. Insulating metal can holder. 16oz. Includes built in bottle opener on the bottom. Holds the tall, skinny cans, regular can, and bottles. Can be used as a regular tumbler as well with additional screw on slider lid with attached handle, included. Includes screw on top for holding.
Metal can holder for sublimation. White. Insulating metal can holder. 16oz. Includes built in bottle opener on the bottom. Holds the tall, skinny cans, regular can, and bottles. Can be used as a regular tumbler as well with additional screw on slider lid with attached handle, included. Includes screw on top for holding cans and bottles. (rubber bottom sold separately if desired) Shiny white sublimation coating that produces vibrant colors. For use in a mug press or convection oven. Convection oven requires the use of shrink wrap to apply pressure during baking, sold separately, and accessories such as rubber bottoms are also available in a separate listing. ***Convection Oven Directions*** PLEASE NOTE: equipment varies and so may your required settings. Please test your own equipment using these baseline recommendations. Apply sublimation transfer on the surface of the tumbler using heat tape. For full wrap designs, make sure you pull the transfer as tightly as possible around the tumbler, then tape very well along the seam and around the top/bottom of the tumbler. Pulling the tape/transfer as tight as possible with no air pockets. If your transfer does not fully cover the tumbler surface, apply blowout/butcher paper to the entire tumbler so that there is no metal showing on the sides. Apply shrink wrap using a heat gun to shrink it tight to the tumbler. Bake in a convection oven at approximately 385-400 degrees F for 5-6 minutes, turning halfway. **If your tumbler is touching a metal surface during baking, the shrink wrap will be more likely to melt!Remove from oven and immediately remove shrink wrap and transfer. TUMBLER WILL BE HOT!!No sealant is necessary on sublimation tumblers. *Hand washing is recommended as the high heat in many dishwashers may reactivate the heat and cause it to bleed. For more information on sublimating these, please visit ACC Sublimation Blanks & Designs Facebook group for videos.

5 in 1 Metal can cooler PREMIUM GLITTER with bottle opener

5 in 1 Metal can cooler with bottle opener, Sublimation ready

Our sublimation can coolers are coated with high quality poly coating and made of 304 food grade stainless steel. These can coolers will produce very

Regular Can Cooler Sublimation Blank

Taho Unsewn Can Cooler Sublimation Blanks (25-Pack

Stainless Can Cooler for Sublimation Blank 12oz

Efficient Set for Everyday Use: Our 16 oz 4in1 can cooler beer glasses set includes 25 cups, 25 lids, 25 Screw lids, and 25 reusable straws. With a

ZREGGUR 25packs 16oz 4-in-1 Can Cooler sublimation Blank tumblers with 2 lid and straw, Double Wall Stainless Steel for Insulated Can Holder,Works

Taho Unsewn Can Cooler Sublimation Blanks (25-Pack

Sublimation Metal Beer Bottle Opener- 2 Sided- by INNOSUB USA

Our Blank High Quality Collapsible Can Coolers are available in many colors and package quantities, and are made of 4mm Thick Polyurethane Foam, which enables them to keep your favorite beverage cool. They can be used at any event or at home, especially because there is no specific message or artwork on them.

PartyPrints 100 Pack Black Blank Can Cooler Sleeves, Customizable Bulk Sublimation Can Coolers, Extra-Thick Collapsible Drink Insulator Sleeve, Beer