Concrete Drainboard Mold Combine

Concrete Drainboard Mold Combine

Concrete Drainboard Mold Combine Drainboard Measurements: 14 1/2" Wide 17" Long 1/4" to 9/16" Sloped Height Channels: Each channel is approximately 3/8" wide, and the set of 5 includes lengths of 12", 14", 16", 14", 12". *Occasional imperfections may be present on Rubber Molds, and can be removed or altered using a sharp utility knife, or a very abrasive sand paper or resin-bound grinding discs. Concrete Drainboard Mold Combine Detail: Rubber Drain Board insert for use with concrete countertop fabrication. The Combine Drainboard has 5 raised round grooves in the mold, which creates 5 depressed concrete channels in the finished concrete. Channels add a visual element to the Drainboard, and are designed to assist in water draining to the sink. Stainless Steel 3/8" round trivet bars are available (Sold Here) in a pre-cut and shaped set of 5 bars to.
Concrete Drainboard Mold Combine Drainboard Measurements: 14 1/2 Wide 17 Long 1/4 to 9/16 Sloped Height Channels: Each channel is approximately 3/8 wide, and the set of 5 includes lengths of 12, 14, 16, 14, 12. *Occasional imperfections may be present on Rubber Molds, and can be removed or altered using a sharp utility knife, or a very abrasive sand paper or resin-bound grinding discs. Concrete Drainboard Mold Combine Detail: Rubber Drain Board insert for use with concrete countertop fabrication. The Combine Drainboard has 5 raised round grooves in the mold, which creates 5 depressed concrete channels in the finished concrete. Channels add a visual element to the Drainboard, and are designed to assist in water draining to the sink. Stainless Steel 3/8 round trivet bars are available (Sold Here) in a pre-cut and shaped set of 5 bars to fit this Combine Drainboard. Clean, nice edges. Fast and simple to use. Add a professional drainboard to your countertop form in minutes. Seamless integral drainboard, countertop, and/or sink. Drainboard slopes toward sink. If the drainboard needs to be shaped (to meet flush with a specific sink), simply cut the rubber mold with a sharp razor knife, or fine tooth jigsaw blade. Made of extremely durable polyurethane that can flex and stay strong. Can be used in pre-cast or poured in place concrete work. Fast and easy to place in a mold, and quick to clean after use. Good for hundreds of uses- Actually gets better with each use as they 'season'. Concrete Drainboard Mold Combine Setup: Place Drainboard Mold in your form and silicone in place. For most applications (Precast), run a silicone a bead across the bottom edge of the Drainboard Mold to create a water-tight seal. If using for poured in place concrete countertops, press the drainboard down into the concrete surface, lightly tapping until flush with the surface, and then place a board or 2x4's across the top of the concrete and Drainboard Mold to hold it in place while the concrete sets up. Use of a Rubber Safe form release is recommended, and will create a smoother finish on the concrete, less air pockets, and make cleaning the rubber mold easier when finished. Vibrate concrete well (either vibrating the concrete, or rapidly tapping the edges of the forms with a hammer or palm sander), to remove as many air pocket voids as possible. Drainboard Mold Removal: After the concrete is sufficiently set up (typically 2-3 days for precast), flip the concrete piece over and remove the Drainboard Mold. In many cases, the mold will stay siliconed to the form when separated from the concrete. Concrete may have small 'bumps' which can be sanded off with a 200 grit sandpaper. These bumps tend to disappear the more the Rubber Drainboard Mold is used, as it becomes seasoned. Fill any air pocket voids with a Concrete Slurry Mix. Rubber Mold Care: Clean with a stiff brush and water after each use. Any silicone left on the forms should be peeled or scraped off (the sooner the easier to remove). Any hardened concrete and difficult to remove silicone can usually be removed using a wire brush. Muriatic Acid can be used to clean of cement residue from the rubber mold in a 20:1 ratio (20 parts water to 1 part muriatic acid). Rub the Drainboard Mold with a stiff nylon brush and the muriatic acid water. Rinse the mold thoroughly with clean water. Store rubber molds out of direct sunlight, laid out flat.

Concrete Countertop with Integral Drainboard by Dale Blayone

Cost to Install Concrete Countertops

, Drainboard Measurements:, 14 1/2 Wide, 17 Long, 1/4 to 9/16 Sloped Height, Channels:, Each channel is approximately 3/8 wide, and the set

Concrete Drainboard Mold Combine

DIY White Concrete Countertops - Chris Loves Julia

Modern Concrete Countertops Kitchen Ideas for Your Home

, Mold Measurements:, 12 3/8 Wide, 15 long, 3/8 to 5/8 Sloped Height., Channels:, 10 Channels: Each channel is approx. 13 Long, 1/4 Wide,

Concrete Drainboard Mold - Journey

Karran 34 Quartz Composite Farmhouse Sink, 60/40 Double Bowl, Bisque, QA-760-BI

Kitchen Sink and Faucet - Shakespeare Home Improvement Co.

The Imperfect Beauty of Concrete Countertops

, Drainboard Measurements:, 14 1/2 Wide, 17 Long, 1/4 to 9/16 Sloped Height, Channels:, Each channel is approximately 3/8 wide, and the set

Concrete Drainboard Mold Combine

Comprehensive procedure of energy slab construction. (a) Installation

, Mold Measurements:, 13 7/8 Wide (at sink), 11 7/8 Wide (end opposite sink), 17 15/16 Long, 1/4-1/2 Sloped Height., Raised Slot Channels are

Concrete Drainboard Insert Mold - Grill

UPIKER Brushed Nickel 16 G Stainless Steel 28 in. Single Bowl Drop-in Topmount Kitchen Sink with Drainboard and Bottom Grid UP2208KSS28012 - The Home Depot